AI assistant for ABB robots

You give the orders.
Robin writes the RAPID.

Nothing reaches the robot until you approve it.

ROBIN · R3 · OMNICOREworking…

“Slow the approach in PickPart to v500.”

  1. Reading PickPart on R3MoveJ pApproach, v1000, z50, tool0
  2. Writing the changeMainModule · 1 line
  3. Preparing a backupon the controller, before the write
- MoveJ pApproach, v1000, z50, tool0;
+ MoveJ pApproach, v500, z50, tool0;
Waiting for your approval

Launch planned for early 2027.

IRC5 + OmniCoreWindowsyour own Claude or ChatGPT accountPro writes to physical controllers

See it work

Click to enlarge. In the enlarged view you can pause.

What you'll ask Robin

Three examples up close, then more of what you can ask.

01

Write it

A new routine, a changed limit, an I/O signal. One sentence, a backup first, written after you approve.

“Operators may only set 1–500.” The screen on the controller changes after your approval.
Real screen
A new I/O signal added to the configuration, with a backup first.
02

Find why it stopped

The event log tells you what happened. Robin finds why and writes the fix. You approve it.

ROBIN · R2 · OMNICOREworking…

“R2 stopped with a motion supervision error. Why?”

  1. Reading the event log50204 Motion supervision · R2
  2. Opening the RAPID behind itPickPart, line 88 · MoveL p40
  3. Checking what the robot carriesgripper closes at line 86 · load is still load0
  4. Planning the fixadd GripLoad loPart; after line 86
Waiting for your approval
Illustrative example on a demo project. Robin is an AI assistant, so its path can differ from case to case.
Real screen
“The program won't start.” Robin reads the log and checks the program.
03

Compare your robots

Four twins. Same program on paper. One behaves differently.

FIG. 02Four twins. One behaves differently.
R1 · MainModule MoveL p10, v500, z10, tGrip;MoveL p20, v500, z10, tGrip;MoveL p30, v500, fine, tGrip;R2 · MainModule MoveL p10, v500, z10, tGrip;MoveL p20, v500, z10, tGrip;MoveL p30, v500, fine, tGrip;R3 · MainModule MoveL p10, v500, z10, tGrip;MoveL p20, v500, z10, tGripOld;MoveL p30, v500, fine, tGrip;R4 · MainModule MoveL p10, v500, z10, tGrip;MoveL p20, v500, z10, tGrip;MoveL p30, v500, fine, tGrip;
Same program on paper. Robin finds the one line that isn't. Illustrative example.

Robin reads every controller, finds the line that differs and prepares the change that brings R3 back in line with the others.
It's written only after you approve.

+

And a lot more

If you'd dig for it on the pendant or in the RAPID editor, ask Robin instead.

  • “Why won't the program start?”
  • “Write a routine to open and close the gripper.”
  • “Port my IRC5 module to OmniCore and load it.”
  • “Create 10 handshake signals for the PLC.”
  • “Add a signal and tie it to a world zone.”
  • “Which options is this controller missing?”
  • “Explain event 50204 and how to clear it.”
  • “Put back yesterday's version of MainModule.”
  • “What changed on R2 since my last visit?”
  • “Find the ABB controllers on this network.”
  • “Back up the whole cell.”
  • “Build a cell-settings screen for the pendant.”

One exception: Robin never touches SafeMove or safety signals.

How a change reaches the robot

Every write goes through all seven stations. Station four is where you decide.

FIG. 01One change, start to finish
READthe controller01PLANthe change02PREVIEWevery line03YOUAllow / Deny04BACKUPon controller05WRITEprograms, config06VERIFYit runs as sent07 pendant conflict → STOPPED then: test in manual, reduced speed
Station 04 on a real screen
“Slow the approach in PickPart.” You see the change, approve it, it's written.

Coming back to ABB?

Back on ABB after a few years and not sure Robin is for you?
Here's what changed on OmniCore, and how Robin handles it.

What's different on OmniCoreHow Robin handles it
Module files.modx / .sysx instead of .mod / .sysPicks the right type when it creates a module
Pendant menusMoved, new FlexPendant appYou skip them: ask Robin for the value, the signal or the event log
Operator screensWeb apps instead of ScreenMakerBuilds settings screens from a chat
Your RW6 modulesMost RAPID carries over, but options may be missingLoads the module on a virtual OmniCore and shows where it fails to link
BackupsSame folders, .modx insideTakes a backup before every change
Remote accessRobot Web Services 2.0: HTTPS, new pathsWorks with both IRC5 and OmniCore

Coming from KUKA or FANUC?
You don't need to know ABB's event codes or menus first.
Robin explains the ABB message and shows the RAPID line behind it.

Robin is almost ready! Launch planned for early 2027.

Join the waitlist

Safe by design

FIG. 03What Robin touches, and what it doesn't
YOUR LAPTOPRobin + your AI RAPID · EVENT LOG · I/Oread PROGRAMS · CONFIGwrite after your approval SAFEMOVE · SAFETY I/Onever
Through ABB's own interfaces, with the user account you give it.
Neverchanges SafeMove, safety signals or stop inputs
Stopswhen someone edited the module on the pendant
Backupon the controller before every write
0 bytesof your code sent to us. Only update and licence checks.

Examples

Someone changed the module on the pendant. Robin doesn't overwrite it.
Asked to relabel a safety signal. Robin refuses.

Who built it

Piotr Ozga

Piotr Ozga · Smart Robot Skills

I spent years programming ABB robots and training others to do it.
On site I kept wishing for one tool: an assistant I could give the task to, while I focus on the program architecture.

So I built Robin.

What you need

Windows10 or 11, 64-bit (tested on 11). No admin rights needed.
RobotWare
  • RW6
  • RW7
  • RW8 (testing in progress)
NetworkYour laptop reaches the controller. Outgoing connections only.
AIYour own Claude account (recommended). Also works with ChatGPT.

What Robin doesn't do yet

Stop typing RAPID line by line. Launch planned for early 2027.

Get it first

FAQ

Does Robin move the robot?

No. It doesn't control motion and never starts the program on its own, on real or virtual controllers.

What if the AI is wrong?

It proposes. You approve every proposed change. A backup is made first. Robin can put back an earlier version of a module from its history, as a change you approve. Restoring a whole controller backup is one command.

Does my code go to you?

No. It stays on your laptop. The parts you ask about go to your AI provider, on your account.

Is it for beginners?

No. It assumes you know industrial robots: you program or commission them, on any brand, not only ABB. It saves you the digging, not the thinking.

What will it cost?

Free on virtual controllers, no time limit.
Pro: 69 € for 30 days or 159 € for 90 days, one-off payment, no subscription.

What happens on day 31 of the trial?

Back to Free. No card was taken, nothing is deleted.
You decide whether to continue with Pro.

Why will Windows warn me?

The installer isn't code-signed yet. Click More info → Run anyway. We publish the SHA-256 with the release so you can check the file.

Does it work without internet on the robot network?

No. Robin works through an AI assistant, and the AI needs internet. Your laptop needs to reach both the robots and the internet.

Get Robin first.

Launch planned for early 2027.
Leave your e-mail and we'll tell you when it's ready.

No spam. Unsubscribe in one click.